The named aor lock was always being locked for writes so a rwlock adds no
benefit and may be slower because rwlocks are biased toward read locking.
Change-Id: I8c5c2c780eb30ce5441832257beeb3506fd12b28
If both channels which should be masqueraded
are in the same serializer:
1st channel will be locked waiting condition 'complete'
2nd channel will be locked waiting condition 'suspended'
On heavy load system a chance that both channels will be in
the same serializer 'pjsip/distibutor' is very high.
To reproduce compile res_pjsip/pjsip_distributor.c with
DISTRIBUTOR_POOL_SIZE=1
Steps to reproduce:
1. Party A calls Party B (bridged call 'AB')
2. Party B places Party A on hold
3. Party B calls Voicemail app (non-bridged call 'BV')
4. Party B attended transfers Party A to voicemail using REFER.
5. When asterisk masquerades calls 'AB' and 'BV',
a deadlock is happened.
This patch adds a suspension indicator to the taskprocessor.
When a session suspends/unsuspends the serializer
it sets the indicator to the appropriate state.
The session checks the suspension indicator before
suspend the serializer.
ASTERISK-26145 #close
Change-Id: Iaaebee60013a58c942ba47b1b4930a63e686663b
When an RTCP packet is sent or received, res_rtp_asterisk generates a
Stasis event that contains the RTCP report as well as the local and
remote addresses that the report pertains to.
The addresses are determined using ast_find_ourip(). For the local
address, this will typically result in a lookup of the hostname of the
server, and then a DNS lookup of that hostname. If you do not have the
host in /etc/hosts, then this results in a full DNS lookup, which can
potentially block for some time.
This is especially problematic when performing RTCP reads, since those
are done on the same thread responsible for reading and writing media.
This patch addresses the issue by performing a lookup of the local
address when RTCP is allocated. We then use this cached local address
for the Stasis events when necessary.
ASTERISK-26280 #close
Reported by Mark Michelson
Change-Id: I3dd61882c2e57036f09f0c390cf38f7c87e9b556
The PJSIP taskprocessors could be overflowed on startup
if there are many (thousands) realtime endpoints
configured with unsolicited mwi.
The PJSIP stack could be totally unresponsive for a few minutes
after boot completed.
This patch creates a separate PJSIP serializers pool for mwi
and makes unsolicited mwi use serializers from this pool.
This patch also adds 2 new global options to tune taskprocessor
alert levels: 'mwi_tps_queue_high' and 'mwi_tps_queue_low'.
This patch also adds new global option 'mwi_disable_initial_unsolicited'
to disable sending unsolicited mwi to all endpoints on startup.
If disabled then unsolicited mwi will start processing
on next endpoint's contact update.
ASTERISK-26230 #close
Change-Id: I4c8ecb82c249eb887930980a800c9f87f28f861a
This change replaces the custom unload process for the outbound
publish module with the common serializer shutdown group.
ASTERISK-25217 #close
Change-Id: I280a0384d860c486202d87d2d674394cca77ffb6
This changes the use of an empty regex for both res_sorcery_config
and res_sorcery_memory to "." instead. This is a more compatible
regular expression which also works on FreeBSD.
ASTERISK-26206 #close
Change-Id: Ia9166dd176f1597555ba22b6931180d0626c1388
This patch removed call of pjsip_tx_data_dec_ref in send_notify
if send_request failed.
The pjsip_dlg_send_request deletes the message on error by itself.
It seems this patch fixes next issues:
ASTERISK-26199
ASTERISK-26166
ASTERISK-26174
Change-Id: I8b05917c93d993f95d604c042ace5f1a5500f59a
The fax_detect_framehook() has the potential to deadlock if an incoming
fax happens during the Playback or similar application.
* Fixed the potential deadlock by not calling ast_async_goto() with the
channel lock held.
* Made always eat the fax detection frame whether there is a fax extension
or not.
* Made only detach the framehook if we detected a fax and not on other
possible frames.
ASTERISK-26216
Reported by: Richard Mudgett
Change-Id: I99da35c26d1cd802626ffb4c1b4eb5b015581b6d
The fax detection timeout option did not work because basically the wrong
variable was checked in fax_detect_framehook(). As a result, the timer
would timeout immediately and disable fax detection.
* Fixed ignoring negative timeout values. We'd complain and then go right
on using the negative value.
* Fixed destroy_faxdetect() in the off-nominal case of an incomplete
object creation.
* Added more range checking to FAXOPT(gateway) timeout parameter.
ASTERISK-26214 #close
Reported by: Richard Mudgett
Change-Id: Idc5e698dfe33572de9840bc68cd9fc043cbad976
The new endpoint option allows the PJSIP channel driver's fax_detect
endpoint option to timeout on a call after the specified number of
seconds into a call. The new feature is disabled if the timeout is set
to zero. The option is disabled by default.
ASTERISK-26214
Reported by: Richard Mudgett
Change-Id: Id5a87375fb2c4f9dc1d4b44c78ec8735ba65453d
If AST_TEST_DEFINE is not conditional to TEST_FRAMEWORK it produces dead
code. This places all existing unit tests into a conditional block if
they weren't already.
ASTERISK-26211 #close
Change-Id: I8ef83ee11cbc991b07b7a37ecb41433e8c734686
With this change, the initial RTP sequence number is randomly chosen not between
0 and 65535 (0xffff) but 0 and 32767 (0x7fff). This assures, the roll-over
counter (ROC) synchronization is not lost for sRTP, when the very first RTP
packets get lost; see http://srtp.sourceforge.net/faq.html#Q6
ASTERISK-26207 #close
Change-Id: I9a527e3aa3ce8f3becc5131d7ba32b57b5845464
The function create_mwi_subscriptions_for_endpoint checks
if there is active contacts by retrieving aors and contacts.
This function is used to create all unsolicited mwi subscriptions
on startup and is used when contact added.
In both cases it's not necessary to check if there are contacts.
The contacts are needed when asterisk sends mwi.
ASTERISK-26200 #close
Change-Id: I98e43bdc97f3c0829951cd9bf5f3c6348c6ac1fa
This commit adds scaffolding in order to support the SILK audio format
on calls. Roughly, this is what is added:
* Cached silk formats. One for each possible sample rate.
* ast_codec structures for each possible sample rate.
* RTP payload mappings for "SILK".
In addition, this change overhauls the res_format_attr_silk file in the
following ways:
* The "samplerate" attribute is scrapped. That's native to the format.
* There are far more checks to ensure that attributes have been
allocated before attempting to reference them.
* We do not SDP fmtp lines for attributes set to 0.
These changes make way to be able to install a codec_silk module and
have it actually work. It also should allow for passthrough silk calls
in Asterisk.
Change-Id: Ieeb39c95a9fecc9246bcfd3c45a6c9b51c59380e
Since July 2014, TLS based protocols (SIP over TLS, Secure WebSockets, HTTPS)
support PFS thanks to ASTERISK-23905. In July 2015, the same feature was added
for DTLS. The source code from main/tcptls.c should have been re-used to ease
security audits. Therefore, this change rolls back the change from July 2015 and
re-uses the code from July 2014. This has the additional benefits to work under
CentOS 7 and enabling not just ECDHE but DHE based cipher suites as well.
ASTERISK-25659 #close
Reported by: StefanEng86, urbaniak, pay123
Tested by: sarumjanuch, traud
patches:
res_rtp_asterisk.patch submitted by sarumjanuch
dtls_centos_step_1.patch submitted by traud
dtls_centos_step_2.patch submitted by traud
Change-Id: I537cadf4421f092a613146b230f2c0ee1be28d5c
aor_observer_deleted() needs to operate on all contacts found for the
deleted AOR instead of only the first one found. This is really only a
problem if there is more than one contact for the AOR.
Change-Id: Id24ac0d5e8c931330231fb45dd2a331a84339dc1
* Fix some whitespace in various routines.
* Rename i to iter in persistent_endpoint_update_state().
* Fix off-nominal copy/paste message wording in
persistent_endpoint_contact_deleted_observer()
Change-Id: Id8e34f5d09e7eebac3af22501c44c1110a3e29d8
The ASTERISK-25904 change-id I8fad8aae9305481469c38d2146e1ba3a56d3108f
patch introduced several regressions when the newly created "Updated"
state goes out for each endpoint registration refresh.
1) It restarted any OPTIONS RTT ping cycle.
2) It would interfere with a currently active ping and throw off that
ping's resulting RTT calculation.
3) It cleared the RTT time each time the endpoint was refreshed.
4) The cleared RTT time was sent out as a statsd update each time.
5) It created two AMI events for each update.
* Revert the original patch and reimplement it. Now the current contact
status state is re-sent instead of the state being momentarily toggled
every time the endpoint refreshes its registration. The statsd events are
not created for the re-sent refresh because they are sent after every
OPTIONS ping.
ASTERISK-26160 #close
Reported by: Matt Jordan
Change-Id: Ie072be790fbb2a8f5c1c874266e4143fa31f66d1
The func_odbc module was modified to ensure that the
previous behavior of using a single database connection
was maintained. This was done by getting a single database
connection and holding on to it. With the new multiple
connection support in res_odbc this will actually starve
every other thread from getting access to the database as
it also maintains the previous behavior of having only
a single database connection.
This change disables the func_odbc specific behavior if
the res_odbc module is running with only a single database
connection active. The connection is only kept for the
duration of the request.
ASTERISK-26177 #close
Change-Id: I9bdbd8a300fb3233877735ad3fd07bce38115b7f
When using TCP transport with chan_pjsip, the TCP_NODELAY
option value was allocated on the stack, then passed as a
pointer to the tcp transport configuration structure, and
later re-used on subsequently created sockets when it was
no longer valid. This patch changes the allocation to be
a static.
ASTERISK-26180 #close
Reported by: Scott Griepentrog
Change-Id: I3251164c7f710dbdab031282f00e30a9770626a0
Some T.38 implementations may send another re-invite after the initial
one which adds additional negotiation details (such as the max bitrate).
Currently this will fail when passthrough is being done in chan_sip as we
do nothing if T.38 is already active.
Other handlers of T.38 inside of Asterisk (such as res_fax) handle this
scenario so this change adds support for it to chan_sip and res_pjsip_t38.
If a request to negotiate is received while T.38 is already enabled a
new re-INVITE is sent and negotiation is done again.
ASTERISK-26179 #close
Change-Id: I0298494d3da6df3219bbfa4be9aa04015043145c
