* acl (named_acl.c)
* cdr
* cel
* ccss
* dnsmgr
* dsp
* enum
* extconfig (config.c)
* features
* http
* indications
* logger
* manager
* plc
* sounds
* udptl
These modules are now loaded at appropriate time by the module loader.
Unlike loadable modules these use AST_MODULE_LOAD_FAILURE on error so
the module loader will abort startup on failure of these modules.
Some of these modules are still initialized or shutdown from outside the
module loader. logger.c is initialized very early and shutdown very
late, manager.c is initialized by the module loader but is shutdown by
the Asterisk core (too much uses it without holding references).
Change-Id: I371a9a45064f20026c492623ea8062d02a1ab97f
Update and extend the configuration_file group and enable linking. Commit other cleanups from multi-version Doxygen testing. Update title that was left behind many years ago.
(issue ASTERISK-20259)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@375182 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Previously, I had added the ast_sched_thread stuff that was a generic scheduler
thread implementation. However, if you used it, it required using different
functions for modifying scheduler contents. This patch reworks how this is
done and just allows you to optionally start a thread on the original scheduler
context structure that has always been there. This makes it trivial to switch
to the generic scheduler thread implementation without having to touch any of
the other code that adds or removes scheduler entries.
In passing, I made some naming tweaks to add ast_ prefixes where they were not
there before.
Review: https://reviewboard.asterisk.org/r/1007/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@299091 65c4cc65-6c06-0410-ace0-fbb531ad65f3
1) Allow users of UDPTL stack to associate a character-string tag with a UDPTL
session, so that log/error/debug messages generated by the UDPTL stack can
be 'connected' to the endpoint that caused them to be generated.
2) Improve comments (and process) of calculating the far end's maximum IFP size
when redundancy mode is in use for error correction.
3) When an IFP larger than the calculated 'far max IFP' size is presented for
writing, truncate it rather than putting in the buffer and allowing the buffer
to overflow; this will cause the ends to retrain to a lower bit rate that
produces IFPs of an appropriate size if possible, and if not possible, the
FAX transfer will fail completely. In these cases, it is due to the one endpoint
supplying a T38FaxMaxDatagram value that is improperly calculated and is
too low to be of use; we have configuration options available to override
this behavior.
4) Eliminate use of T38FaxMaxDatagram value in udptl.conf; it is no longer
needed.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@231692 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The udptl-updates branch that was merged yesterday failed to properly send back
T.38 SDP responses with the correct error correction mode, if the incoming SDP
from the other end caused us to change error correction modes. This patch
corrects that situation.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@208548 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Over the past couple of months, a number of issues with Asterisk
negotiating (and successfully completing) T.38 sessions with various
endpoints have been found. This patch attempts to address many of
them, primarily focused around ensuring that the endpoints'
MaxDatagram size is honored, and in addition by ensuring that T.38
session parameter negotiation is performed correctly according to the
ITU T.38 Recommendation.
The major changes here are:
1) T.38 applications in Asterisk (app_fax) only generate/receive IFP
packets, they do not ever work with UDPTL packets. As a result of
this, they cannot be allowed to generate packets that would overflow
the other endpoints' MaxDatagram size after the UDPTL stack adds any
error correction information. With this patch, the application is told
the maximum *IFP* size it can generate, based on a calculation using
the far end MaxDatagram size and the active error correction mode on
the T.38 session. The same is true for sending *our* MaxDatagram size
to the remote endpoint; it is computed from the value that the
application says it can accept (for a single IFP packet) combined with
the active error correction mode.
2) All treatment of T.38 session parameters as 'capabilities' in
chan_sip has been removed; these parameters are not at all like
audio/video stream capabilities. There are strict rules to follow for
computing an answer to a T.38 offer, and chan_sip now follows those
rules, using the desired parameters from the application (or channel)
that wants to accept the T.38 negotiation.
3) chan_sip now stores and forwards ast_control_t38_parameters
structures for tracking 'our' and 'their' T.38 session parameters;
this greatly simplifies negotiation, especially for pass-through
calls.
4) Since T.38 negotiation without specifying parameters or receiving
the final negotiated parameters is not very worthwhile, the
AST_CONTROL_T38 control frame has been removed. A note has been added
to UPGRADE.txt about this removal, since any out-of-tree applications
that use it will no longer function properly until they are upgraded
to use AST_CONTROL_T38_PARAMETERS.
Review: https://reviewboard.asterisk.org/r/310/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@208464 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Copied from my review board description:
This is a continuation of the API changes documentation started for describing
changes between releases. Most of the API changes were pretty simple needing
only to be brought to attention via the new "Asterisk API Changes" list.
However, if you see anything that needs further explanation feel free to
supplement what is there. The current method of documenting is to add (in the
header file): \version <ver number> <description of changes> and then to add
the function to the change list in doxyref.h on the AstAPIChanges page. I also
made sure all the functions that were newly added were tagged with \since
1.6.1. I think this is a good habit to start both for the historical aspect as
well as for the future ability to easily add a "New Asterisk API" page.
Review: http://reviewboard.digium.com/r/190/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@180719 65c4cc65-6c06-0410-ace0-fbb531ad65f3
