This reverts commit 93332cb1d0.
Unfortunately, the aforementioned commit caused a regression (incoming calls
would eventually disconnect). Thus it is being removed.
ASTERISK-26523 #close
ASTERISK-25270
Change-Id: Ibf5586adc303073a8eac667a4cbfdb6be184a64d
If in sip.conf (general section) set option register_retry_403=no,
the command "sip show settings" return value:
Outbound reg. retry 403:0
If in sip.conf (general section) set option register_retry_403=yes,
the command "sip show settings" return value:
Outbound reg. retry 403:-1
* In static char "sip show settings" for "Outbound.reg. retry 403"
option use AST_CLI_YESNO
ASTERISK-26476 #close
Change-Id: I3c14272f05f1067bd2aeaa8b3ef9cf8fcb12dcf9
Previously, the settings videosupport=always and videosupport=yes behaved
identically and unconditionally caused a video offer to be sent in the SDP on
an outgoing call. This was a regression introduced with commit
5a1d90e1fb in Asterisk 1.6.1.
This commit restores correct behavior: videosupport=always causes a video offer
to be sent unconditionally, while videosupport=yes will only offer video on an
outbound channel if the incoming channel it is bridged to also supports video.
That way, the device receiving the outgoing call can display the correct user
interface elements for audio or video and will not unnecessarily show a blank
video window on an audio-only call.
ASTERISK-17470 #close
Change-Id: I782f4409d436114dbc97061c3570c0cd24f7c3ae
In the SIP channel driver chan_sip, auto_comedia was expected to be used in
tandem with auto_force_rport. Or stated differently: Only when auto_force_rport
was chosen (the default), auto_comedia worked. This change allows auto_comedia
to be set independently of the state of (auto_)force_rport. For example,
nat=force_rport,auto_comedia is useful for IPv4/IPv6 Dual Stack deployments
when IPv6 clients are behind a Firewall.
ASTERISK-26457 #close
Change-Id: Ib29d66c6dbb61648e371e01fc36c6978ddae5bc2
In the SIP channel driver chan_sip, the default is "auto_force_rport". When no
NAT was detected, for example in case of IPv6, Asterisk uses the IP address
from the headers within the SIP-REGISTER for subsequent SIP signaling. When
the remote party specifies support for Symmetric Response (RFC 3581) via the
parameter "rport", Asterisk should not extract the port from the SIP headers
but reuse the port of the transport. This did not happen because of a typo.
ASTERISK-26438 #close
Change-Id: If6e7891848aaf96666dee5305695f7c6667cd5a6
For the channel driver chan_sip, you specify externhost=example.com in sip.conf
when your Asterisk is behind a NAT and your IP address is assigned dynamically.
Or stated differently: You do not have a static IP address to use "externaddr"
directly. This NAT support is quite handy but just about IPv4. Previously,
Asterisk resolved "externhost" to any IP version. When the first DNS answer
resolved to an IPv6, Asterisk sent an IPv6 in SIP/SDP for origin (o=) and
connection (c=). This happened in outgoing SIP-REGISTER and while answering
SIP-INVITE. If the remote peer is IPv4-only, it might not handle o=/c= with an
IPv6. This change makes sure, no IPv6 is resolved anymore for "externhost".
ASTERISK-18232 #close
Reported by: Jacek Kowalski
Tested by: Alexander Traud
patches:
changes.patch submitted by Alessandro Crespi
Change-Id: If68eedbeff65bd1c1d8a9ed921c02ba464b32dac
Users upgrading from asterisk 13.5 to a later version and who use
realtime with peers that have mailboxes were experiencing runaway
situations that manifested as a continuous stream of taskprocessor
congestion errors, memory leaks and an unresponsive chan_sip.
A related issue was that setting rtcachefriends=no NEVER worked in
asterisk 13 (since the move to stasis). In 13.5 and earlier, when a
peer tried to register, all of the stasis threads would block and
chan_sip would again become unresponsive. After 13.5, the runaway
would happen.
There were a number of causes...
* mwi_event_cb was (indirectly) calling build_peer even though calls to
mwi_event_cb are often caused by build_peer.
* In an effort to prevent chan_sip from being unloaded while messages
were still in flight, destroy_mailboxes was calling
stasis_unsubscribe_and_join but in some cases waited forever for the
final message.
* add_peer_mailboxes wasn't properly marking the existing mailboxes
on a peer as "keep" so build_peer would always delete them all.
* add_peer_mwi_subs was unsubscribing existing mailbox subscriptions
then just creating them again.
All of this was causing a flood of subscribes and unsubscribes on
multiple threads all for the same peer and mailbox.
Fixes...
* add_peer_mailboxes now marks mailboxes correctly and build_peer only
deletes the ones that really are no longer needed by the peer.
* add_peer_mwi_subs now only adds subscriptions marked as "new" instead
of unsubscribing and resubscribing everything. It also adds the peer
object's address to the mailbox instead of its name to the subscription
userdata so mwi_event_cb doesn't have to call build_peer.
With these changes, with rtcachefriends=yes (the most common setting),
there are no leaks, locks, loops or crashes at shutdown.
rtcachefriends=no still causes leaks but at least it doesn't lock, loop
or crash. Since making rtcachefriends=no work wasnt in scope for this
issue, further work will have to be deferred to a separate patch.
Side fixes...
* The ast_lock_track structure had a member named "thread" which gdb
doesn't like since it conflicts with it's "thread" command. That
member was renamed to "thread_id".
ASTERISK-25468 #close
Change-Id: I07519ef7f092629e1e844f855abd279d6475cdd0
Change-Id I1cd33453c77c56c8e1394cd60a6f17bb61c1d957 Enable Session-Timers for
SIP over TCP (and TLS) also disables SIP retransmits in chan_sip for non-UDP
connections, allowing the TCP layer to handle the retransmits. Unfortunately,
this caused sessions to be terminated with a retransmit timeout becasue it
stopped at the point of the first retrans call.
This patch waits for the 64*T1 timer to expire instead.
ASTERISK-19968
Change-Id: I844f26801aada10bc94e9bebe6e151f0a8443204
Previously, the Contact was stored only on initial INVITE and on any
18X and 200. That meant that after re-INVITEs from *us* the Contact
could get updated, but after re-INVITEs from the *peer*, it did not.
This changeset fixes this inconsistency, properly allowing target
refreshes through re-INVITES (RFC3261, 12.2).
If your strictrtp setting allows it, this change allows you to switch
the source IP of a connected/calling device mid-call with a simple
re-INVITE from the new IP.
ASTERISK-26358 #close
Change-Id: Ibb8512054ab27c8c3d2514022568fde943bf2435
In some scenarios dialog_initialize_rtp can be called multiple times on
the same dialog. This can cause RTP instances to be leaked along with
multiple file descriptors for each instance.
This change makes it so the existing RTP instances are destroyed and
not overwritten, stopping the memory leak.
ASTERISK-26272 #close
patches:
ASTERISK-26272-13.patch submitted by Corey Farrell (license 5909)
Change-Id: Id529de1184c68f2f4d254ab41a1f458dafdb5f73
Certain SNOM phones send so-called "optional crypto" in their SDP body.
Regular SRTP setup looks like this:
m=audio 64620 RTP/SAVP 8 0 9 99 3 18 4 101
a=crypto:1 AES_CM_128_HMAC_SHA1_32 inline:...
SNOM-style "optional crypto" looks like this:
m=audio 61438 RTP/AVP 8 0 9 99 3 18 4 101
a=crypto:1 AES_CM_128_HMAC_SHA1_32 inline:...
A crypto line is supplied, but the m-line does not have SAVP.
When res_srtp.so is *not* loaded, then chan_sip.so treats the optional
crypto as regular RTP, but when res_srtp.so *is* loaded, it refuses the
incoming call with the following message:
WARNING: process_sdp: Failed to receive SDP offer/answer with
required SRTP crypto attributes for audio
For platforms that want to start providing SRTP this presents a
compatibility problem.
This changeset lets chan_sip handle the SDP as if no crypto-line was
supplied: i.e. accept the call as regular RTP, just like it did before
res_srtp was loaded.
Now you'll get this informative warning instead:
WARNING: Ignoring crypto attribute in SDP because RTP transport is
insecure
ASTERISK-23989 #close
Reported by: Olle Johansson
Change-Id: I91a15ae05a0296e398d6b65f53bb11afde1d80e2
Historically, Asterisk has always specified annexb=no for the g729 format.
However, when using res_pjsip no format attribute was specified. This patch
makes it so the SDP now contains a format attribute line with annexb=no.
Note, that this means only g729a is negotiated. Even for pass through support.
According to rfc7261 the type of annex used (a or b) is dependent upon the
answerer. However, Asterisk being a back to back user agent makes this tricky
to support at this time, thus we only allow annex 'a' for now.
ASTERISK-26228 #close
patches:
res_format_attr_g729.c submitted by Jason Parker (license 4993)
Change-Id: I76bc20cc0a01af01536e9915afef319c269c22d0
This updates func_channel.c and main/message.c to use a generic xpointer
include instead of including info from each channel driver. Now the
name attribute of info is CHANNEL or CHANNEL_EXAMPLES to be included in
documentation for func_channel. Setting the name attribute of info to
MessageToInfo or MessageFromInfo causes it to be included in the
MessageSend application and AMI action.
Change-Id: I89fd8276a3250824241a618009714267d3a8d1ea
Packets are read regulary, when there is no data in buffer fr->frametype
is AST_FRAME_NULL. There was no check of frametype and lastrtprx always
updated and, therefore, rtptimeout did not work at all.
ASTERISK-25270 #close
Change-Id: If3b5ca0dbb822582a86eb7d01dcae4e83448c41d
Asterisk defaults to timers=accept/refresher=uas. In that scenario, only in that
scenario, Sessions-Timers (RFC 4028) had no effect via TCP. This change enables
Session-Timers for SIP over TCP (and for SIP over TLS).
However with longer international calls via TCP, the SIP channel might break,
because all hops on the Internet route must stay online (have not a single power
outage, for example). Therefore with Session-Timers enabled (which are enabled
at default), you might see dropped calls. Consequently even with this change,
you might be better-off going for session-timers=refuse in your sip.conf.
ASTERISK-19968 #close
Change-Id: I1cd33453c77c56c8e1394cd60a6f17bb61c1d957
sip_show_channels locks the dialogs container first then locks each
sip_pvt so it can spit out the details. The rest of sip dialog
processing locks the sip_pvt first then locks the dialogs container
if it needs to. Both lock in the order they need but deadlocks can
result. To fix, sip_show_channels and sip_show_channelstats have
been converted to use an iterator rather than ao2_callback. This way
the container is locked only while getting the next entry and is
unlocked when the callback is called.
ASTERISK-23013 #close
Change-Id: Id9980419909e811f89484950ed46ef117b9eb990
The sip_read() has the potential to deadlock if an incoming fax happens
during the Playback or similar application.
* Fixed the potential deadlock by not calling ast_async_goto() with the
channel lock held.
* Made always eat the fax detection frame whether there is a fax extension
or not.
ASTERISK-26216
Reported by: Richard Mudgett
Change-Id: I6d3f5cccd4b77c3aa6ffc1a54c0f6bde61c9278e
Cleanup the peer reference when stasis_subscription_final_message is
true. Also free peer_name even if peer exists, after reload a new
peer_name will be allocated.
ASTERISK-26193 #close
Change-Id: If7ecd52facdc5c227f701c760841e3f6ca53cc69
* get_sip_pvt_from_replaces leaks sip_pvt_ptr on any error.
* build_peer leaks peer on failure to allocate the endpoint.
This patch fixes get_sip_pvt by using an RAII_VAR, build_peer is fixed
with an unref in the appropriate place.
ASTERISK-26184 #close
Change-Id: I728b424648ad041409f7d90880f4c28b3ce2ca12
Some T.38 implementations may send another re-invite after the initial
one which adds additional negotiation details (such as the max bitrate).
Currently this will fail when passthrough is being done in chan_sip as we
do nothing if T.38 is already active.
Other handlers of T.38 inside of Asterisk (such as res_fax) handle this
scenario so this change adds support for it to chan_sip and res_pjsip_t38.
If a request to negotiate is received while T.38 is already enabled a
new re-INVITE is sent and negotiation is done again.
ASTERISK-26179 #close
Change-Id: I0298494d3da6df3219bbfa4be9aa04015043145c
This change removes hardcoded SDP parsing and generation for
Siren7 and Siren14 from chan_sip and moves it to format attribute
modules so it can also be used by chan_pjsip.
With this the fmtp lines for both are added with the bitrate
information.
ASTERISK-26021
Change-Id: Ibb004eda37a14c0a35ef0613f6237977fc800037
Currently chan_sip can give weird messages if the contacts don't
fit in the From: or To: headers. This fix changes the from,to and
invite variables to use ast_str, allocates and deallocates them and
resizes them if needed.
ASTERISK-26069 #close
Change-Id: I1b68fcbddca6f6cc7d7a92fe1cb0d5430282b2b3
A change to glibc 2.22 changed the order of the sockadddr_storage
members which caused the places where we do an initialization of
ast_sockaddr with '{ { 0, 0, } }' to fail compilation. Those
initializers (which we shouldn't have been using anyway) have been
replaced with memsets.
Change-Id: Idd1b3b320903d8771bfe221f0b015685de628fa4
When chan_sip does a re-INVITE to refresh a session and authentication
is required, the INVITE with the Authorization header containes a
second Session-Expires header without the ";refersher=" parameter.
This is causing some proxies to return a 400. Also, when Asterisk is
the uas and the refresher, it is including the Session-Expires and
Min-SE headers in OPTIONS messages which is not allowed per RFC4028.
This patch (based on the reporter's) Checks to see if a Session-Expires
header is already in the message before adding another one. It also
checks that the method is INVITE or UPDATE.
ASTERISK-26030 #close
Change-Id: I58a7b07bab5a3177748d8a7034fb8ad8e11ce1d9
The unload process currently tells each TCP/TLS to terminate but
does not wait for them to do so. This introduces a race condition
where the container holding the threads may be destroyed before
the threads are able to remove themselves from it. When they
finally do the container is invalid and can't be used causing a
crash.
A previous change existed which waited a bit to wait for any
stranglers to finish. This change extends this and waits longer.
ASTERISK-25961 #close
Change-Id: Idc6262b670ca49ede32061159e323b7b63c6f3c6
Since Stasis has been introduced, an attempt to send AMI messages by an
autocreated peer caused a crash, and all events from autocreated peers were
semi-inadvertently disabled altogether in 0b83761. This change restores the
disabled functionality.
ASTERISK-25950
Change-Id: Iecc350f23db603fadb2f302064643ebe9664e974
Asterisk 13.7.0 included a fix for ASTERISK-24543, not to send all those
codecs, which the caller did not request/support. That fix was not complete
because on the second Session Timer all codecs were sent again. Some VoIP/SIP
clients interpreted that complete codec-list as a change in the SIP session.
Because of that, Asterisk did not send the RTP audio via NAT anymore which
created a non-audio scenario after the second Session Timer fired.
ASTERISK-24543 #close
Change-Id: I1881827816ab7fd47eb4287a95961179b34a0b66
check_via() already skips leading blanks where the sent-by address (with the
optional port) should be placed.
Since RFC 3261 allows for blanks between the port ant the Via parameters:
> https://tools.ietf.org/html/rfc3261#section-20.42
(actually it allows a lot of blanks more ;-)). I just switched from
ast_skip_blanks() to ast_strip() on the local copy of the string.
ASTERISK-21301 #close
Change-Id: Ie5b8fe5a07067b7c0dc9bcdd1707e99b23b02b06
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023 #close
Change-Id: I96d429c57a48861fd8bde63dd93db4e92dc3adb6
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I2e40de89efc8ae6e8850771d089ca44bc604b508
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: If595e4456cd059d7171880c7f354e844c21b5f5f
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I9c11b9d597468f63916c99e1dabff9f4a46f84c1
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Fix retrans_pkt() to call check_pendings() with both the owner channel
and the private objects locked as required.
* Refactor dialog retransmission packet list to safely remove packet
nodes. The list nodes are now ao2 objects. The list has a ref and the
scheduled entry has a ref.
ASTERISK-25023
Change-Id: I50926d81be53f4cd3d572a3292cd25f563f59641
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Made always run check_pendings() under the scheduler thread so scheduler
ids can be checked safely.
ASTERISK-25023
Change-Id: Ia834d6edd5bdb47c163e4ecf884428a4a8b17d52
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I6d65269151ba95e0d8fe4e9e611881cde2ab4900
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
* Fix clearing autokillid in __sip_autodestruct() even though we could
reschedule.
ASTERISK-25023
Change-Id: I450580dbf26e2e3952ee6628c735b001565c368f
This patch is part of a series to resolve deadlocks in chan_sip.c.
Stopping a scheduled event can result in a deadlock if the scheduled event
is running when you try to stop the event. If you hold a lock needed by
the scheduled event while trying to stop the scheduled event then a
deadlock can happen. The general strategy for resolving the deadlock
potential is to push the actual starting and stopping of the scheduled
events off onto the scheduler/do_monitor() thread by scheduling an
immediate one shot scheduled event. Some restructuring may be needed
because the code may assume that the start/stop of the scheduled events is
immediate.
ASTERISK-25023
Change-Id: I98a694fd42bc81436c83aa92de03226e6e4e3f48
This patch is part of a series to resolve deadlocks in chan_sip.c.
* Make dialog_unlink_all() unschedule all items at once in the sched
thread.
ASTERISK-25023
Change-Id: I7743072fb228836e8228b72f6dc46c8cc50b3fb4
This patch is part of a series to resolve deadlocks in chan_sip.c.
The reordering of chan_sip's shutdown is to handle any immediate events
that get put onto the scheduler so resources aren't leaked. The typical
immediate events at this time are going to be concerned with stopping
other scheduled events.
ASTERISK-25023
Change-Id: I3f6540717634f6f2e84d8531a054976f2bbb9d20
