Explains new options for detecting DTMF CID on fxo lines
(issue #9096)
Reported by: fleed
Patches:
chan_dahid_sample_config.patch uploaded by sum (license 766)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@224144 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Ability has been added to both manager command SIPnotify as well as console
command sip notify. Message body is stored in the "Content" variable. An
example is present in sip_notify.conf.
(closes issue #13926)
Reported by: jthurman
Patches:
sip-notify-svn189463.diff uploaded by gareth (license 208)
Tested by: gareth
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@224035 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch adds support for TCP/TLS in the Contact header when using
NAT, specifically externip or externhost. The original issue was that
Asterisk sent 5060 as the port in the contact header whether TLS was
used or not. Additionally, this patch adds 2 config options to sip.conf,
specifically externtcpport and externtlsport. This allows a user to
specify different external ports for TCP and TLS other than those used
internally, this is especially useful in in a PAT/port redirection setup.
Thanks to ebroad for reporting the issue and providing the patch!
(closes issue #15880)
Reported by: ebroad
Patches:
portmap.patch uploaded by ebroad (license 878)
externtXXport_v2.patch uploaded by ebroad (license 878)
Tested by: ebroad
Review: https://reviewboard.asterisk.org/r/392/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222398 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Many T.38 endpoints incorrectly send the maximum IFP frame size they can accept
as the T38FaxMaxDatagram value in their SDP, when in fact this value is
supposed to be the maximum UDPTL payload size (datagram size) they can accept.
If the value they supply is small enough (a commonly supplied value is '72'),
T.38 UDPTL transmissions will likely fail completely because the UDPTL packets
will not have enough room for a primary IFP frame and the redundancy used for
error correction. If this occurs, the Asterisk UDPTL stack will emit log messages
warning that data loss may occur, and that the value may need to be overridden.
This patch extends the 't38pt_udptl' configuration option in sip.conf to allow
the administrator to override the value supplied by the remote endpoint and
supply a value that allows T.38 FAX transmissions to be successful with that
endpoint. In addition, in any SIP call where the override takes effect, a debug
message will be printed to that effect. This patch also removes the
T38FaxMaxDatagram configuration option from udptl.conf.sample, since it has not
actually had any effect for a number of releases.
In addition, this patch cleans up the T.38 documentation in sip.conf.sample
(which incorrectly documented that T.38 support was passthrough only).
(issue #15586)
Reported by: globalnetinc
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@222110 65c4cc65-6c06-0410-ace0-fbb531ad65f3
chan_sip has had the ability to control T.38 FAX error correction mode on a per-peer
(or global) basis for a couple of releases now, which is where it should have been
all along. This patch removes the ability to configure it in udptl.conf, but issues
a warning if the user tries to do, telling them to look at sip.conf.sample for how
to configure it now. For any SIP peers that are T.38 enabled in sip.conf, there is
already a default for FEC error correction even if the user does not specify any mode,
so this change will not turn off error correction by default, it will have the same
default value that has been in the udptl.conf sample file.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221592 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221360 | mnicholson | 2009-09-30 14:36:06 -0500 (Wed, 30 Sep 2009) | 10 lines
Fix SRV lookup and Request-URI generation in chan_sip.
This patch adds a new field "portinuri" to the sip dialog struct and the sip peer struct. That field is used during RURI generation to determine if the port should be included in the RURI. It is also used in some places to determine if an SRV lookup should occur.
(closes issue #14418)
Reported by: klaus3000
Tested by: klaus3000, mnicholson
Review: https://reviewboard.asterisk.org/r/369/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221432 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r221086 | twilson | 2009-09-30 09:49:11 -0500 (Wed, 30 Sep 2009) | 25 lines
Change the SSRC by default when our media stream changes
Be default, change SSRC when doing an audio stream changes Asterisk doesn't
honor marker bit when reinvited to already-bridged RTP streams,resulting in
far-end stack discarding packets with "old" timestamps that areactually part of
a new stream. This patch sends AST_CONTROL_SRCUPDATE whenever there is a
reinvite, unless the 'constantssrc' is set to true in sip.conf.
The original issue reported to Digium support detailed the following situation:
ITSP <-> Asterisk 1.4.26.2 <-> SIP-based Application Server Call comes in
fromITSP, Asterisk dials the app server which sends a re-invite back
toAsterisk--not to negotiate to send media directly to the ITSP, but to
indicatethat it's changing the stream it's sending to Asterisk. The app
servergenerates a new SSRC, sequence numbers, timestamps, and sets the marker
bit on the new stream. Asterisk passes through the teimstamp of the new stream,
butdoes not reset the SSRC, sequence numbers, or set the marker bit.
When the timestamp on the new stream is older than the timestamp on the
originalstream, the ITSP (which doesn't know there has been any change) discards
the newframes because it thinks they are too old. This patch addresses this by
changing the SSRC on a stream update unless constantssrc=true is set in
sip.conf.
Review: https://reviewboard.asterisk.org/r/374/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221266 65c4cc65-6c06-0410-ace0-fbb531ad65f3
JABBER_RECEIVE (along with JabberSend) makes Asterisk interact with users over
XMPP to process calls.
SendText can be used instead of JabberSend in the context of XMPP based voice
channels (chan_gtalk and chan_jingle).
(closes issue #12569)
Reported by: eech55
Tested by: phsultan, asannucci, lmadsen, jtodd, maxgo
Review: https://reviewboard.asterisk.org/r/88/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@220457 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r216430 | oej | 2009-09-04 15:45:48 +0200 (Fre, 04 Sep 2009) | 27 lines
Make apps send PROGRESS control frame for early media and fix too early media issue in SIP
The issue at hand is that some legacy (dying) PBX systems send empty media frames on PRI
links *before* any call progress. The SIP channel receives these frames and by default
signals 183 Session progress and starts sending media. This will cause phones to
play silence and ignore the later 180 ringing message. A bad user experience.
The fix is twofold:
- We discovered that asterisk apps that support early media ("noanswer") did not send
any PROGRESS frame to indicate early media. Fixed.
- We introduce a setting in chan_sip so that users can disable any relay of media frames
before the outbound channel actually indicates any sort of call progress.
In 1.4, 1.6.0 and 1.6.1, this will be disabled for backward compatibility. In later versions
of Asterisk, this will be enabled. We don't assume that it will change your Asterisk
phone experience - only for the better.
We encourage third-party application developers to make sure that if they have applications
that wants to send early media, add a PROGRESS control frame transmission to make sure that
all channel drivers actually will start sending early media. This has not been the default
in Asterisk previous to this patch, so if you got inspiration from our code, you need to
update accordingly. Sorry for the trouble and thanks for your support.
This code has been running for a few months in a large scale installation (over 250
servers with PRI and/or BRI links to old PBX systems).
That's no proof that this is an excellent patch, but, well, it's tested :-)
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@216438 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Allows characters that are otherwise used as delimiters to be used within
certain fields (like the secret).
(closes issue #15008, closes issue #15672)
Reported by: tilghman
Patches:
20090818__issue15008.diff.txt uploaded by tilghman (license 14)
Tested by: lmadsen, tilghman
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@213098 65c4cc65-6c06-0410-ace0-fbb531ad65f3
It is clear from multiple mailing list, forum, wiki and other sorts of posts
that users don't really understand the effects that the 'canreinvite' config
option actually has, and that in some cases they think that setting it to 'no'
will actually cause various other features (T.38, MOH, etc.) to not work properly,
when in fact this is not the case. This patch changes the proper name of the
option to what it should have been from the beginning ('directmedia'), but
preserves backwards compatibility for existing configurations.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@210190 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/branches/1.4
........
r209131 | mmichelson | 2009-07-27 12:44:06 -0500 (Mon, 27 Jul 2009) | 18 lines
Allow for UDPTL to use only even-numbered ports if desired.
There are some VoIP providers out there that will not accept SDP
offers with odd numbered UDPTL ports. While it is my personal opinion
that these VoIP providers are misinterpreting RFC 2327, it really is
not a big deal to play along with their silly little games. Of course,
since restricting UDPTL ports to only even numbers reduces the range
of available ports by half, so the option to use only even port numbers
is off by default. A user can enable the behavior by setting
use_even_ports=yes in udptl.conf.
(closes issue #15182)
Reported by: CGMChris
Patches:
15182.patch uploaded by mmichelson (license 60)
Tested by: CGMChris
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@209132 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Requiring 'module reload' to reload everything, including
core etc makes russell very unhappy.
The default configuration already loads the 'friendly' aliases template.
Added 'reload=module reload' to that template.
Also removed the comment in main/cli.c that reload should come back.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@208813 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is a continuation of revision 885 to LibPRI (Capture and expose the Reverse
Charging Indication IE on ISDN PRI) which added the ability to get/set Reverse
Charging Indication in LibPRI. This patch adds the ability to specify RCI on
the outbound leg of a PRI call from within Asterisk, by prefixing the dialed
number with a capital 'C' like:
...,Dial(DAHDI/g1/C4445556666)
And to read it off an inbound channel:
exten => s,1,Set(RCI=${CHANNEL(reversecharge)})
Thanks again to rmudgett for the thorough review.
(closes issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/303/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204749 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Someone asked yesterday, "is there a good reason why we can't just put these
modules in Asterisk?". After a brief discussion, as long as the modules are
clearly set aside in their own directory and not enabled by default, it is
perfectly fine.
For more information about why a module goes in addons, see README-addons.txt.
chan_ooh323 does not currently compile as it is behind some trunk API updates.
However, it will not build by default, so it should be okay for now.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204413 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This might seem like a legitimate comment that merely needed semicolon
prefixes, but in reality, the adaptive layer is designed to allow arbitrary
CDR variables, without needing the use of a userfield to store multiple items.
It's therefore not only invalid syntax but also goes against the intent of the
adaptive method.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204069 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The original patch for this was written by Brett Bryant, and I split it out into
it's own module.
(closes issue #12876)
Reported by: bbryant
Patches:
06162008_cdr_custom_syslog.diff uploaded by bbryant (license 36)
05212009_cdr_syslog.patch uploaded by seanbright (license 71)
Tested by: seanbright
Review: https://reviewboard.asterisk.org/r/297/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203846 65c4cc65-6c06-0410-ace0-fbb531ad65f3
