Changed areas in sig_pri to set the digital flag using a callback that will
also set the corresponding flag in chan_dahdi. Modified dahdi_request slightly
so that if a bearer is marked as digital, that information is available when
creating the new channel.
(closes issue #16151)
Reported by: alecdavis
Patch based on bug_16151.diff.txt uploaded by alecdavis (license 585)
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@231058 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Since ISDN works like SIP and not analog ports in regard to devices, the
device state based on the ISDN channel number could not work. This has
not been an issue until the advent of PTMP NT mode. Previously, ISDN
lines were used as trunks and did not have to keep track of specific
devices.
As an interim solution until device states are properly implemented, the
channel name is being changed to the following format to use the generic
device state support:
DAHDI/i<span>/<number>[:<subaddress>]-<sequence-number>
Dialplan hints would thus be:
exten => xxx,hint,DAHDI/i2/5551212
This will work with the following restrictions:
* The number of devices/phones cannot exceed the number of B channels.
(i.e., BRI has 2)
* Each device/phone can only have one number. No shared MSN's.
* The phones/devices probably should not use subaddressing.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@226882 65c4cc65-6c06-0410-ace0-fbb531ad65f3
* Added handling of received HOLD/RETRIEVE messages and the optional ability
to transfer a held call on disconnect similar to an analog phone.
* Added CallRerouting/CallDeflection support for Q.SIG, ETSI PTP, ETSI PTMP.
Will reroute/deflect an outgoing call when receive the message.
Can use the DAHDISendCallreroutingFacility to send the message for the
supported switches.
* Added ability to send/receive keypad digits in the SETUP message.
Send keypad digits in SETUP message: Dial(DAHDI/g1[/K<keypad_digits>][/extension])
Access any received keypad digits in SETUP message by: ${CHANNEL(keypad_digits)}
* Added support for BRI PTMP NT mode.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@225692 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The PRI channels can no longer change the channel name if a different B
channel is selected during call negotiation. To prevent using the channel
name to infer what B channel a call is using and to avoid name collisions,
the channel name format is changed.
The new channel naming for PRI channels is:
DAHDI/ISDN-<span>-<sequence-number>
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@221701 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Add Connected Line Presentation (COLP) support to chan_dahdi/libpri as an
addition to issue 8824. This is the chan_dahdi/sig_pri portion. COLP
support is now available for any switch for which libpri supports COLP
(currently ETSI PTP, ETSI PTMP, and Q.SIG) with this patch.
(closes issue #14068)
Tested by: rmudgett
Review: https://reviewboard.asterisk.org/r/340/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@213007 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The wrong logic was being used in chan_dahdi to convert a sig_pri_chan
to the proper libpri channel number. The most significant bit must only
be set only when trunk groups are being used.
(closes issue #15452)
Reported by: alecdavis
Patches:
bug15452.patch uploaded by jpeeler (license 325)
Tested by: alecdavis
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@208267 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This readds the proper setting of the flag and is really a continuation of
r205731. The flag was being set properly in sig_analog, but use of the
newly added set_dialing callback allowed for some simplification in
chan_dahdi.
(closes issue #15486)
Reported by: rmudgett
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@206767 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Also go back and wrap all of the places that use the specific reverse charge
APIs with preprocessor conditionals.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204919 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This is a continuation of revision 885 to LibPRI (Capture and expose the Reverse
Charging Indication IE on ISDN PRI) which added the ability to get/set Reverse
Charging Indication in LibPRI. This patch adds the ability to specify RCI on
the outbound leg of a PRI call from within Asterisk, by prefixing the dialed
number with a capital 'C' like:
...,Dial(DAHDI/g1/C4445556666)
And to read it off an inbound channel:
exten => s,1,Set(RCI=${CHANNEL(reversecharge)})
Thanks again to rmudgett for the thorough review.
(closes issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/303/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@204749 65c4cc65-6c06-0410-ace0-fbb531ad65f3
CEL is the new system for logging channel events. This was inspired after
facing many problems trying to represent what is possible to happen to a call
in Asterisk using CDR records. For more information on CEL, see the built in
HTML or PDF documentation generated from the files in doc/tex/.
Many thanks to Steve Murphy (murf) and Brian Degenhardt (bmd) for their hard
work developing this code. Also, thanks to Matt Nicholson (mnicholson) and
Sean Bright (seanbright) for their assistance in the final push to get this
code ready for Asterisk trunk.
Review: https://reviewboard.asterisk.org/r/239/
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203638 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This merge splits the PRI/BRI signaling logic out of chan_dahdi.c into
sig_pri.c. Functionality in theory should not change (mostly). A few trivial
changes were made in sig_analog with verbose messages and commenting.
git-svn-id: https://origsvn.digium.com/svn/asterisk/trunk@203304 65c4cc65-6c06-0410-ace0-fbb531ad65f3
