The new inband_on_setup_ack option causes Asterisk to assume inband audio
may be present when a SETUP_ACKNOWLEDGE message is received.
Q.931 Section 5.1.3 says that in scenarios with overlap dialing, when a
dialtone is sent from the network side, progress indicator 8 "Inband info
now available" MAY be sent to the CPE if no digits were received with the
SETUP. It is thus implied that the ie is mandatory if digits came with
the SETUP and dialtone is needed. This option should be enabled, when the
network sends dialtone and you want to hear it, but the network doesn't
send the progress indicator when needed.
NOTE: For Q.SIG setups this option should be enabled when outgoing overlap
dialing is also enabled because Q.SIG does not send the progress indicator
with the SETUP ACK.
The commit -r413714 (AST-1338) which causes this issue was dealing with a
SIP-to-ISDN interoperability issue.
This commit is a merge of the two patches indicated below.
ASTERISK-23897 #close
Reported by: Pavel Troller
Patches:
pri-4.diff (license #6302) patch uploaded by Pavel Troller
jira_asterisk_23897_v11.patch (license #5621) patch uploaded by rmudgett
Review: https://reviewboard.asterisk.org/r/3633/
........
Merged revisions 417956 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417957 65c4cc65-6c06-0410-ace0-fbb531ad65f3
A loop in ast_careful_fwrite exists that will continually attempt to write to
a file stream, even in the presence of EAGAIN/EINTR errors. However, if a
connection that uses ast_careful_fwrite closes suddenly, ast_careful_fwrite's
call to fflush may return EAGAIN/EINTER along with EOF. A subsequent call to
fflush will return EOF but not clear errno, resulting in an infinite loop.
This patch clears errno after it is detected and handled the loop, such that
any subsequent call to fflush will not get erroneously stuck.
Review: https://reviewboard.asterisk.org/r/3704
#ASTERISK-23984 #close
Reported by: Steve Davies
patches:
fflush_loop_fix uploaded by one47 (License 5012)
........
Merged revisions 417797 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417798 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This change fixes up DTLS support in res_rtp_asterisk so it can accept and provide
a SHA-256 fingerprint, so it occurs on RTCP, and so it occurs after ICE negotiation
completes. Configuration options to chan_sip have also been added to allow behavior
to be tweaked (such as forcing the AVP type media transports in SDP).
ASTERISK-22961 #close
Reported by: Jay Jideliov
Review: https://reviewboard.asterisk.org/r/3679/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417677 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch is essentially a backport of a small portion of r397526 from
ASTERISK-21981. In that patch, pass through support and format attribute
negotiation was added for Opus. Part of that included being more tolerant to
whitespace in the fmtp line of an SDP; that part of the patch is being
applied here.
As the author of the backport pointed out, in SDP, the fmtp line is allowed to
include whitespace between attributes. RFC 3267 chapter 8.3 (from 2001)
includes an example for this. This was not removed in the updated RFC 4867 in
2007.
Review: https://reviewboard.asterisk.org/r/3658
ASTERISK-23916 #close
Reported by: Alexander Traud
patches:
sdpFMTPspace_Asterisk11.patch uploaded by Alexander Traud (License 6520)
........
Merged revisions 417587 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417588 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When using FEC, with span=3 and entries=4 Asterisk will attempt to repair
the packet with sequence number 5, as it will see that packet -4 is
missing. The result is Asterisk sending garbage packets that can kill a
fax.
This patch adds a check to see if the sequence number is valid before
checking if the packet is missing.
Review: https://reviewboard.asterisk.org/r/3657/
#ASTERISK-23908 #close
Reported by: Torrey Searle
patches:
udptl_fec.patch uploaded by Torrey Searle (License 5334)
........
Merged revisions 417318 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417320 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a client takes a long time to process information received from Asterisk,
a write operation using fwrite may fail to write all information. This causes
the underlying file stream to be in an unknown state, such that the socket
must be disconnected. Unfortunately, there are two problems with this in
Asterisk's existing websocket code:
1. Periodically, during the read loop, Asterisk must write to the connected
websocket to respond to pings. As such, Asterisk maintains a reference to
the session during the loop. When ast_http_websocket_write fails, it may
cause the session to decrement its ref count, but this in and of itself
does not break the read loop. The read loop's write, on the other hand,
does not break the loop if it fails. This causes the socket to get in a
'stuck' state, preventing the client from reconnecting to the server.
2. More importantly, however, is that the fwrite in ast_http_websocket_write
fails with a large volume of data when the client takes awhile to process
the information. When it does fail, it fails writing only a portion of
the bytes. With some debugging, it was shown that this was failing in a
similar fashion to ASTERISK-12767. Switching this over to ast_careful_fwrite
with a long enough timeout solved the problem.
ASTERISK-23917 #close
Reported by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3624/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417310 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The features.conf sample can be a bit confusing about what parking options can be set only in the general context, or both in the general context (for the default parking lot) and in other parking lot contexts. A bug was filed due to confusion and a little googling will show lots of other confused users.
Despite some comments on the individual options, it still reads in a confusing way. In this patch I separate out those options with some headings in to attempt a better layout. I went ahead and modified other headings in the file, or added them to facilitate better visual scanning.
ASTERISK-23667
Review: https://reviewboard.asterisk.org/r/3622/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417077 65c4cc65-6c06-0410-ace0-fbb531ad65f3
AST_FORTIFY_SOURCE is automatically set in ./Makefile even if DONT_OPTIMIZE
is set in menuselect. This causes gcc to complain that _FORTIFY_SOURCE
requires optimization and the build will fail. You can specify
"make AST_FORTIFY_SOURCE=''" but I always forget.
This patch moves the set of AST_FORTIFY_SOURCE to Makefile.rules and only
sets it if DONT_OPTIMIZE is "no". The move is necessary because the
top-level Makefile doesn't include menuselect.makeopts.
This doesn't solve the entire problem however because res_config_mysql
seems to force _FORTIFY_SOURCE so res_config_mysql has to be disabled
for now if DONT_OPTIMIZE is set.
Tested by: George Joseph
Review: https://reviewboard.asterisk.org/r/3664/
........
Merged revisions 417016 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@417017 65c4cc65-6c06-0410-ace0-fbb531ad65f3
ast_ext_tool_check.m4 isn't handling cases where a path to a package is
provided (E.G. --with-mysqlclient=/some/sysroot) and the package has a config
tool (E.G. mysql_config) and the package has its own subdirectories in include
or lib. For example, mysql's libraries are in ${MYSQLCLIENT_DIR}/usr/lib/mysql
but ast_ext_tool_check sets MYSQLCLIENT_LIB to ${MYSQLCLIENT_DIR}/usr/lib.
libxml2 has the same problem with its includes. They're in
${LIBXML2_DIR}/usr/include/libxml2 not directly in ${LIBXML2_DIR}/usr/include.
Both cause configure to fail and there are others in the same boat.
The problem is caused by logic in ast_ext_tool_check that overrides the result
of the config tool's --cflags and --libs options if package_DIR is set.
This patch prepends package_DIR (if specified) to the -L and -I results from
the package's config tool instead of overriding them.
A regenerated ./configure and include/asterisk/autoconfig.h.in are included
but can be regenerated by running ./bootstrap.sh at any time.
Tested by: George Joseph
Tested by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3550/
........
Merged revisions 416929 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416930 65c4cc65-6c06-0410-ace0-fbb531ad65f3
ast_ext_tool_check.m4 isn't handling cases where a path to a package is
provided (E.G. --with-mysqlclient=/some/sysroot) and the package has a config
tool (E.G. mysql_config) and the package has its own subdirectories in include
or lib. For example, mysql's libraries are in ${MYSQLCLIENT_DIR}/usr/lib/mysql
but ast_ext_tool_check sets MYSQLCLIENT_LIB to ${MYSQLCLIENT_DIR}/usr/lib.
libxml2 has the same problem with its includes. They're in
${LIBXML2_DIR}/usr/include/libxml2 not directly in ${LIBXML2_DIR}/usr/include.
Both cause configure to fail and there are others in the same boat.
The problem is caused by logic in ast_ext_tool_check that overrides the result
of the config tool's --cflags and --libs options if package_DIR is set.
This patch prepends package_DIR (if specified) to the -L and -I results from
the package's config tool instead of overriding them.
Tested by: George Joseph
Tested by: Matt Jordan
Review: https://reviewboard.asterisk.org/r/3550/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416870 65c4cc65-6c06-0410-ace0-fbb531ad65f3
AST_MODFLAG_GLOBAL_SYMBOLS was causing the module to be incorrectly loaded
before pbx_config. pbx_config was therefore blowing away contexts that were
created by pbx_lua. With AST_MODFLAG_DEFAULT the load order is now correct
and contexs are being properly merged. AST_MODFLAG_GLOBAL_SYMBOLS was not
needed anyway since no other modules needed its global symbols that early.
ASTERISK-23818 #close
Reported by: Dennis Guse
Tested by: Dennis Guse
Tested by: George Joseph
Review: https://reviewboard.asterisk.org/r/3629/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416668 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The sample extensions.lua was causing pbx_lua to fail to load when parsing
'app.goto("default", "s", 1)' because in Lua 5.2, 'goto' is now a reserved
word. This patch adds guidance to extensions.lua.sample and changed
'app.goto("default", "s", 1)' to 'app.['goto']("default", "s", 1)'.
ASTERISK-23844 #close
Reported by: rnewton
Tested by: gtjoseph
Review: https://reviewboard.asterisk.org/r/3627/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416581 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Currently, music on hold will stop and then start again from the
beginning if ast_moh_start() is called multiple times. This can happen
if a call is put on hold repeatedly (the channel receives multiple
HOLD control frames) and can be triggered from ARI by starting MoH on a
channel multiple times. This is fairly jarring/annoying to users.
This change prevents MoH from being restarted if the requested music
class is the same as the one currently playing.
This includes an extra check to prevent the errors previously
experienced in the testsuite and has 100+ test runs behind it.
Review: https://reviewboard.asterisk.org/r/3615/
........
Merged revisions 416439 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416440 65c4cc65-6c06-0410-ace0-fbb531ad65f3
This patch reverts r416150. When the comparison between mohclass->name and
state->class->name is made, you are not guaranteed that (a) state->class is
non-NULL or that state or state->class are in a safe state.
Crashes caught by the bridges/transfer_capabilities test.
........
Merged revisions 416251 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416252 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Currently, music on hold will stop and then start again from the
beginning if ast_moh_start() is called multiple times. This can happen
if a call is put on hold repeatedly (the channel receives multiple
HOLD control frames) and can be triggered from ARI by starting MoH on a
channel multiple times. This is fairly jarring/annoying to users.
This change prevents MoH from being restarted if the requested music
class is the same as the one currently playing.
Review: https://reviewboard.asterisk.org/r/3615/
........
Merged revisions 416150 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@416151 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Simply establishing a TCP connection and never sending anything to the
configured HTTP port in http.conf will tie up a HTTP connection. Since
there is a maximum number of open HTTP sessions allowed at a time you can
block legitimate connections.
A similar problem exists if a HTTP request is started but never finished.
* Added http.conf session_inactivity timer option to close HTTP
connections that aren't doing anything. Defaults to 30000 ms.
* Removed the undocumented manager.conf block-sockets option. It
interferes with TCP/TLS inactivity timeouts.
* AMI and SIP TLS connections now have better authentication timeout
protection. Though I didn't remove the bizzare TLS timeout polling code
from chan_sip.
* chan_sip can now handle SSL certificate renegotiations in the middle of
a session. It couldn't do that before because the socket was non-blocking
and the SSL calls were not restarted as documented by the OpenSSL
documentation.
* Fixed an off nominal leak of the ssl struct in
handle_tcptls_connection() if the FILE stream failed to open and the SSL
certificate negotiations failed.
The patch creates a custom FILE stream handler to give the created FILE
streams inactivity timeout and timeout after a specific moment in time
capability. This approach eliminates the need for code using the FILE
stream to be redesigned to deal with the timeouts.
This patch indirectly fixes most of ASTERISK-18345 by fixing the usage of
the SSL_read/SSL_write operations.
ASTERISK-23673 #close
Reported by: Richard Mudgett
........
Merged revisions 415841 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415854 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In app_queue, device state changes arrive in event messages and
update the queue member status value. That value is checked in
get_member_status() to decide that the caller should leave when
there are no available members. Although event messages can be
delayed by other activity, there is no adverse affect by lagged
status except in one specific case: there is only one available
member, it was just rung, and leavewhenempty is enabled set for
ringing members. This change adds a direct check of the device
state only under this condition where the caller may be dropped
incorrectly, resolving this issue without affecting performance
of app_queue normally.
AST-1248 #close
Review: https://reviewboard.asterisk.org/r/3595/
Reported by: Thomas Arimont
........
Merged revisions 415833 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415835 65c4cc65-6c06-0410-ace0-fbb531ad65f3
MixMonitor AMI commands StartMixMonitor and StopMixMonitor lacked class
authorization. StopMixMonitor now requires that the manager user either have
the call or system class authorization. StartMixMonitor is a slightly larger
issue since it can execute shell commands if the right arguments are passed
into it, and we consider this a permission escalation. A security release
will be issued for problem this shortly.
ASTERISK-23609 #close
Reported by: Corey Farrell
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415825 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The supplied hash function to a container must be idempotent given the
object's key value to figure out which container bucket the object belongs
in. Returning a random number or the current container count is not
idempotent. The "computed hash" value doesn't help find the object later
in those cases.
* Fixed the format_list container to actually be a list since that is how
the container is used. Conceptually, if more than 283 formats were added
to the format_list then odd things may have happened before the fix.
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415728 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Replaced a stray echo that should've been a message call in
safe_asterisk. I'm using the contents of the old message inside the
if $NOTIFY so peoples log parsing scripts won't get confused by new
messages. I'll clean that up in trunk.
(Note that a 'make install' still won't overwrite your old safe_asterisk
if it exists. See ASTERISK-21965.)
ASTERISK-23492 #close
........
Merged revisions 415521 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415522 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The twisted logic determining if a config file should be reloaded was
mostly broken and disabled. The incorrect test that ASTERISK-23383 fixed
actually reenabled the broken logic. The incorrect test was causing the
timestamp to always be cleared which caused config files with includes to
always be reloaded.
* Made wildcard includes always cause a reload. Determining if a file was
deleted cannot be determined without restructuring the cache to determine
if any files are missing from the last files actually loaded. Also
without refactoring config_text_file_load(), the glob loop couldn't check
more than one file for changes anyway.
* Made remove the cache entry if the file no longer exists when trying to
get its timestamp or it is no longer a regular file. This fixes the
corner case where the file was loaded, then deleted, then the config
reloaded, then the file restored with the same timestamp, and then the
config reloaded again.
* Made remove the cache entry include list when actually loading the file.
This gets rid of any stale includes the file had from the last time the
file was loaded.
ASTERISK-23683 #close
Reported by: tootai
Review: https://reviewboard.asterisk.org/r/3575/
........
Merged revisions 415225 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415229 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Prior to this patch, users waiting to enter a ConfBridge were not considered
when muted via the CLI or via AMI. Instead, a confusing message would be
emitted stating that the channel did not exist.
This patch allows a user to be muted when waiting to enter a ConfBridge
conference. This is equivalent to start when muted, only toggled via the CLI
or AMI.
Review: https://reviewboard.asterisk.org/r/3582
ASTERISK-23824 #close
patches:
rb3582.patch uploaded by tm1000 (License 6524)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415206 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Cleans up the safe_asterisk script and adds the ASTSAFE_FOREGROUND
option that allows the debian asterisk init script to capture the
right pid.
* Drop the vim #modeline which wasn't used. Use test consistently
without the odd configure xno syntax. Double quote all paths.
General cleanup.
* Don't output message()s to the console but only to TTY if set.
* Allow TTY to be "no" as well as empty (debian compatibility with
debian/patches/safe_asterisk-config).
* Add option to export ASTSAFE_FOREGROUND=1 from the init script
that calls this to disable backgrounding. Debian uses a similar
method in debian/patches/safe_asterisk-nobg).
ASTERISK-23492 #close
Review: https://reviewboard.asterisk.org/r/3574/
........
Merged revisions 415132 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415171 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Conference names were not checked for maximum length, allowing unexpected
behaviour. This change adds checking to ensure the maximum length is not
exceeded. The maximum length is also changed from 32 to AST_MAX_EXTENSION.
ASTERISK-23035 #close
Reported by: Iñaki Cívico
Tested by: Iñaki Cívico
Patches:
confbridge-enforce_max-1.8.patch uploaded by coreyfarrell (license 5909)
confbridge-enforce_max-11up.patch uploaded by coreyfarrell (license 5909)
........
Merged revisions 415060 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@415066 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The change that removed the fixed size buffers in odbc-related code --
removing arbitrary column width limits -- was incomplete. This change
adds: no segfault on writesql without insertsql and return value checks
after strdup.
While I was in the vicinity I cleaned up the linefeeds in the odbc
function descriptions, moved some code for clarity, removed some blobs
and noted (but didn't fix) that the 'odbc write ... exec' CLI command
doesn't behave as the dialplan equivalent when insertsql= is used.
#ASTERISK-23582 #close
Review: https://reviewboard.asterisk.org/r/3579/
........
Merged revisions 414997 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414998 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When invoking UpdateConfig AMI action with Action set to EmptyCat, Asterisk
will make all categories empty in the config but the one requested with a
Cat variable. This is due to a bug in ast_category_empty (main/config.c)
that makes an incorrect comparison for a category name.
This patch corrects the comparison such that only the requested category
is cleared.
Review: https://reviewboard.asterisk.org/r/3573/
ASTERISK-23803 #close
Reported by: zvision
patches:
manager.c.diff uploaded by zvision (License 5755)
........
Merged revisions 414880 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414881 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Dynamic and pattern matching hints should not be checked for their last
known state until they are instantiated by subscribers.
(closes issue AFS-56)
Reported by: John Hardin
Patch AFS-56-pbx.diff submitted by Matt Jordan (license 6283)
........
Merged revisions 414813 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414859 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Asterisk started counting the session timer at INVITE while the other
end correctly started at 200. This meant that for short session-expiries
(90 seconds) combined with long ringing times (e.g. 30 seconds), asterisk
would wrongly assume that the timer was hit before the other end thought
it was time to send a session refresh. This resulted in prematurely
ended calls.
This changes the session timer to start counting first at 200 like RFC
says it should.
(Also removed a few excess NULL checks that would never hit, because if
they did, asterisk would have crashed already.)
ASTERISK-22551 #close
Reported by: i2045
Review: https://reviewboard.asterisk.org/r/3562/
........
Merged revisions 414620 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414628 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The ODBC realtime driver uses ^NN parameter encoding to cope with the
special meaning of the semi-colon. A semi-colon in a field is
interpreted as if the key was supplied twice, something which isn't
otherwise possible with fixed database columns. E.g. allow=alaw;ulaw
is parsed as allow=alaw and allow=ulaw. A literal semi-colon is
rewritten to ^3B when stored in the database.
The module uses a stringfield to efficiently store the encoded
parameters. However, this stringfield wasn't always freed in some
off-nominal cases.
Commit r413241 fixed initialization so the encoding for INSERT and
DELETE queries wouldn't crash. (Only SELECTs and UPDATEs worked
apparently.) But that commit forgot the frees. This change cleans
that up.
Review: https://reviewboard.asterisk.org/r/3555/
........
Merged revisions 414564 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414565 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Occasionally, when the last marked user leaves the conference, waitmarked
users don't get MOH if MOH is supposed to be played while a waitmarked
user is waiting for another marked user.
* Made not interrupt MOH when the user is a waitmarked user. The
waitmarked user doesn't need to hear any leave announcements from the
conference as the user would have already heard different leave
announcements if they were enabled. Apparently DAHDI occasionally sends
unending non-silent streams to these users or a normal user still in the
conference has continuous high background noise. These non-silent streams
cause MOH to be suspended while the never ending "announcement" is played.
Issue caused by ASTERISK-13680.
AST-1349 #close
Reported by: Tyler Stewart
Review: https://reviewboard.asterisk.org/r/3543/
........
Merged revisions 414401 from http://svn.asterisk.org/svn/asterisk/branches/1.8
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/11@414402 65c4cc65-6c06-0410-ace0-fbb531ad65f3
