When a T.38 re-INVITE failed with an 488 or 606 answer, we should
fallback to audio fax by send a re-re-INVITE without T.38. The
function is backported from 1.6 asterisk.
(closes issue #16795)
Reported by: vrban
(closes issue #16692)
Reported by: vrban
Patches:
t38_fallback_to_audio_v3.patch uploaded by vrban (license 756)
Tested by: lmadsen, vrban, haggard
https://reviewboard.asterisk.org/r/514/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@266579 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The needringing bit was being read in dahdi_read after answering thereby
setting the state to ringing from up. This clears needringing upon answering
so that is no longer possible.
(closes issue #17067)
Reported by: tzafrir
Patches:
needringing.diff uploaded by tzafrir (license 46)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@260434 65c4cc65-6c06-0410-ace0-fbb531ad65f3
The code handling DTMF CallerID drops digits on long CallerID numbers and
may timeout waiting for the first ring with shorter numbers.
The DTMF emulation mode was not turned off when processing DTMF CallerID.
When the emulation code gets behind in processing the DTMF digits it can
skip a digit.
For shorter numbers, the timeout may have been too short. I increased it
from 2 seconds to 4 seconds. Four seconds is a typical time between rings
for many countries.
(closes issue #16460)
Reported by: sum
Patches:
issue16460.patch uploaded by rmudgett (license 664)
issue16460_v1.6.2.patch uploaded by rmudgett (license 664)
Tested by: sum, rmudgett
Review: https://reviewboard.asterisk.org/r/634/
JIRA SWP-562
JIRA AST-334
JIRA SWP-901
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@260195 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Issue_1.
In the local_hangup() 3 locks must be held at the same time... pvt, pvt->chan,
and pvt->owner. Proper deadlock avoidance is done when the channel to hangup
is the outbound chan_local channel, but when it is not the outbound channel we
have an issue... We attempt to do deadlock avoidance only on the tech pvt, when
both the tech pvt and the pvt->owner are locked coming into that loop. By
never giving up the pvt->owner channel deadlock avoidance is not entirely possible.
This patch resolves that by doing deadlock avoidance on both the pvt->owner and the pvt
when trying to get the pvt->chan lock.
Issue_2.
ast_prod() is used in ast_activate_generator() to queue a frame on the channel
and make the channel's read function get called. This function is used in
ast_activate_generator() while the channel is locked, which mean's the channel
will have a lock both from the generator code and the frame_queue code by the
time it gets to chan_local.c's local_queue_frame code... local_queue_frame
contains some of the same crazy deadlock avoidance that local_hangup requires,
and this recursive lock prevents that deadlock avoidance from happening correctly.
This patch removes ast_prod() from the channel lock so only one lock is held during
the local_queue_frame function.
(closes issue #17185)
Reported by: schmoozecom
Patches:
issue_17185_v1.diff uploaded by dvossel (license 671)
issue_17185_v2.diff uploaded by dvossel (license 671)
Tested by: schmoozecom, GameGamer43
Review: https://reviewboard.asterisk.org/r/631/
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@259858 65c4cc65-6c06-0410-ace0-fbb531ad65f3
"WARNING[28406]: chan_dahdi.c:6873 ss_thread: CallerID feed failed: Success"
Changed the warning to "Failed to decode CallerID on channel 'name'". The
message before it is likely more specific about why the CallerID decode
failed.
SWP-501
AST-283
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@259531 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Issue #7321 implements a new chan_dahdi configuration option. However, a
change mentioned in the issue was never implemented. This is the change
that will allow the feature to work.
I added a note to chan_dahdi.conf.sample about the feature.
(closes issue #17143)
Reported by: djensen99
Patches:
diff.txt uploaded by djensen99 (license NA) (One line change)
Tested by: djensen99
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@259270 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When a reply to a deregistration is lost in transmit, the client retries the
deregistration. Previously, this would cause a realtime/autocreate peer to be
loaded back into memory, after it had already been correctly purged. Instead,
we just want to resend the reply without loading the peer.
(closes issue #16908)
Reported by: kkm
Patches:
20100412__issue16908.diff.txt uploaded by tilghman (license 14)
Tested by: kkm
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@257467 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/trunk
........
r252089 | twilson | 2010-03-12 16:04:51 -0600 (Fri, 12 Mar 2010) | 20 lines
Only change the RTP ssrc when we see that it has changed
This change basically reverts the change reviewed in
https://reviewboard.asterisk.org/r/374/ and instead limits the
updating of the RTP synchronization source to only those times when we
detect that the other side of the conversation has changed the ssrc.
The problem is that SRCUPDATE control frames are sent many times where
we don't want a new ssrc, including whenever Asterisk has to send DTMF
in a normal bridge. This is also not the first time that this mistake
has been made. The initial implementation of the ast_rtp_new_source
function also changed the ssrc--and then it was removed because of
this same issue. Then, we put it back in again to fix a different
issue. This patch attempts to only change the ssrc when we see that
the other side of the conversation has changed the ssrc.
It also renames some functions to make their purpose more clear.
Review: https://reviewboard.asterisk.org/r/540/
........
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@252175 65c4cc65-6c06-0410-ace0-fbb531ad65f3
From the issue:
The automatic overnight line tests (or manual ones) used on UK (BT) lines causes
a red alarm on a dahdi / TDM400P connected channel. This is because the line
uses voltage tests (battery loss) and polarity reversal. The polarity reversal
causes chan_dahdi to initiate v23 CallerID processing but during this the event
DAHDI_EVENT_NOALARM is ignored so that the alarm is never cleared.
(closes issue #14163)
Reported by: jedi98
Patches:
chan_dahdi-1.4-inalarm.diff uploaded by jedi98 (license 653)
Tested by: mattbrown, Chainsaw, mikeeccleston
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@250480 65c4cc65-6c06-0410-ace0-fbb531ad65f3
When Asterisk receives an IAX2 TXREQ packet, try_transfer()
will call store_by_transfercallno() to link the chan_iax2_pvt
struct into iax_transfercallno_pvts. If a duplicate TXREQ
packet is received for the same call, the pvt struct will be
linked into iax_transfercallno_pvts multiple times. This patch
fixes this. Thanks rain for debugging this and providing a patch!
(closes issue #16904)
Reported by: rain
Patches:
iax2-double-txreq-fix.diff uploaded by rain (license 327)
Tested by: rain, dvossel
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@250394 65c4cc65-6c06-0410-ace0-fbb531ad65f3
In this case, attended transfers were broken due to ast_feature_request_and_dial
detecting the channel being set to up before the answer frame could be read and
therefore failing to mark the channel as ready. This fix is a regression fix for
244785, which should continue to work properly as well.
(closes issue #16816)
Reported by: jamhed
Tested by: jamhed, corruptor
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@249536 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Following Q.931 5.2.4
When the user has determined that sufficient call information has been received the
user shall stop T302 and send CALL PROCEEDING to the network.
Previously timeouts were possible if the dialplan took a long time to issue any
response back to the network.
Verified that our local TELCO also does the same.
(issue #16789)
Reported by: alecdavis
Patches:
based on overlap_receiving_trunk.diff.txt uploaded by alecdavis (license 585)
Tested by: alecdavis
(closes issue #16789)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@249365 65c4cc65-6c06-0410-ace0-fbb531ad65f3
https://origsvn.digium.com/svn/asterisk/be/branches/C.2-...
..........
r247904 | rmudgett | 2010-02-19 10:49:44 -0600 (Fri, 19 Feb 2010) | 49 lines
Make chan_misdn DTMF processing consistent with other channel technologies.
The processing of DTMF tones on the receiving side of an ISDN channel is
inconsistent with the way it is handled in other channels, especially
DAHDI analog. This causes DTMF tones sent from an ISDN phone to be
doubled at the connected party.
We are using the following 2 options of misdn.conf
1) astdtmf=yes
2) senddtmf=yes
Option one is necessary because the asterisk DSP DTMF detection is better
than mISDN's internal DSP. Not as many false positives.
Option two is necessary to transmit DTMF tones end to end when mISDN
channels are connected to SIP channels with out of band DTMF for example.
The symptom is that DTMF tones sent by an ISDN phone are doubled on the
way through asterisk when two mISDN channels are connected with a Local
channel in between or if it is bridged to an analog channel.
The doubling of DTMF tones is because DTMF is passed inband to asterisk by
the mISDN channel and passed out of band once again after the release of
the DTMF tone. Passing it inband is wrong. Neither an analog channel nor
SIP channel passes DTMF inband if configured to inband DTMF. Analog and
SIP channels filter out the DTMF tones because they use the voice frames
returned by ast_dsp_process. But chan_misdn passes the unfiltered input
voice frames instead.
To overcome one aspect of the problem, the doubling of DTMF tones when two
mISDN channels are directly bridged, someone made an 'optimization', where
in that case the DTMF tone passed out-of-band to the peer channel is not
translated to an inband tone at the transmit side. This optimization is
bad because it does not work in general. For example, analog channels or
mISDN channels when bridged through an intermediary local channel will
generate DTMF tones from out-of-band information. Also, of course, it
must not be done when there is no inband DTMF available.
This patch fixes the issue. Now chan_misdn will filter the received
inband DTMF signal the same as other channel types.
Another change included: No need to build an extra translation path
because ast_process_dsp does it if required.
Patches:
misdn-dtmf.patch
JIRA ABE-2080
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@247910 65c4cc65-6c06-0410-ace0-fbb531ad65f3
2^15 = 32768 which is the maximum allowed iax2 callnumber.
Creating the iaxs and iaxsl array of size 32768 means the maximum
callnumber is actually out of bounds. This causes a nasty crash.
(closes issue #15997)
Reported by: exarv
Patches:
iax_fix.diff uploaded by dvossel (license 671)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@245792 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Previously local channels channel state never changed. This became problematic
when the state of the other side of the local channel was lost, for example
during a masquerade. Changing the state of the local channel allows for the
scenario to be detected when the channel state is set to ringing, but the peer
isn't ringing. The specific problem scenario is described in 164201. Although
this was noted on one of the issues, here is the tested dialplan verified to
work:
exten => 9700,1,Dial(Local/*9700@default&Local/#9700@default)
exten => *9700,1,Set(GLOBAL(TESTCHAN)=${CHANNEL:0:${MATH(${LEN(${CHANNEL})}-1):0:2}}1)
exten => *9700,n,wait(3) ;3 works, 1 did not
exten => *9700,n,Dial(SIP/5001)
exten => #9700,1,Wait(1) ;1 works, 3 did not
exten => #9700,n,ChannelRedirect(${TESTCHAN},parkedcalls,701,1)
(closes issue #14992)
Reported by: davidw
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@244785 65c4cc65-6c06-0410-ace0-fbb531ad65f3
One must always lock the agents list lock before the agent private. agent_read
locks the private immediately, so locking the agents list lock is not an
option (which is what agent_logoff requires). Because agent_read already
has access to the agent private all that is necessary is to do the required
hanging up that agent_logoff performed.
(closes issue #16321)
Reported by: valon24
Patches:
bug16321.patch uploaded by jpeeler (license 325)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@241227 65c4cc65-6c06-0410-ace0-fbb531ad65f3
A signed short was used to represent a callnumber. This is makes
it possible to attempt to access the iaxs array with a negative
index.
(closes issue #16565)
Reported by: jensvb
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@238411 65c4cc65-6c06-0410-ace0-fbb531ad65f3
It is possible for a second ACK to come in for a retransmitted message.
If an ack does not match an unacked message in our queue, restore the previous
p->method as this ACK is completely ignored.
(closes issue #16295)
Reported by: omolenkamp
Patches:
issue16295_v2.diff uploaded by dvossel (license 671)
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@236062 65c4cc65-6c06-0410-ace0-fbb531ad65f3
There where still cases where the 183 keep-alive mechanism would not stop
sending 183's even though the Asterisk server had sent a final reply to
the invite.
EDVX-28
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@234492 65c4cc65-6c06-0410-ace0-fbb531ad65f3
(The digital flag actually represents a data call.)
(closes issue #15972)
Reported by: udosw
Patches:
transcap_digital_fix.diff.txt uploaded by alecdavis (license 585)
Tested by: alecdavis
git-svn-id: https://origsvn.digium.com/svn/asterisk/branches/1.4@232090 65c4cc65-6c06-0410-ace0-fbb531ad65f3
Paul Belanger
David Vossel
Jeff Peeler
Richard Mudgett
Tilghman Lesher
Russell Bryant
Terry Wilson
Alec L Davis
Kevin P. Fleming
Mark Michelson
Olle Johansson
Matthew Nicholson